Find HS Code and trade information for PLASTIC ROD

Declaration Analysis: PLASTIC ROD - HS Code Classification & Duty Information

This analysis details the HS code classifications and associated duties for “PLASTIC ROD” based on the provided information. We'll break down each HS code, explain its meaning, and outline the relevant tax implications.

Important Note: The correct HS code is crucial for accurate duty assessment and smooth customs clearance. Please carefully review the product details against the descriptions below to ensure the most appropriate code is selected.

1. HS Code: 3916.10.00.00 – Monofilament of which any cross-sectional dimension exceeds 1 mm, rods, sticks and profile shapes, whether or not surface-worked but not otherwise worked, of plastics: Of polymers of ethylene

• Chapter 39: Plastics and articles thereof. This chapter covers a wide range of plastic materials and products.
• 3916: Monofilament of which any cross-sectional dimension exceeds 1 mm, rods, sticks and profile shapes, whether or not surface-worked but not otherwise worked, of plastics. This specifically targets plastic rods, sticks, and profiles exceeding 1mm in cross-section.
• 3916.10: Of polymers of ethylene. This sub-heading narrows the classification to plastic rods made from polymers of ethylene (e.g., polyethylene - PE, including LDPE, HDPE, LLDPE).
• 3916.10.00.00: Further specifies the product.

Duty Information:

• Basic Duty: 5.8%
• Additional Duty: 25.0%
• Total Duty (Current): 60.8%
• Additional Duty (Post April 2, 2025): 30.0% (Total duty will increase to 65.8% after this date)

Example Products: Polyethylene (PE) pipes, PE rods used for construction, LDPE/HDPE/LLDPE rods.

2. HS Code: 3916.90.10.00 – Monofilament of which any cross-sectional dimension exceeds 1 mm, rods, sticks and profile shapes, whether or not surface-worked but not otherwise worked, of plastics: Of other plastics: Of acrylic polymers

• Chapter 39: Plastics and articles thereof.
• 3916: Monofilament of which any cross-sectional dimension exceeds 1 mm, rods, sticks and profile shapes, whether or not surface-worked but not otherwise worked, of plastics.
• 3916.90: Of other plastics. This covers plastic rods, sticks, and profiles not specifically covered in other 3916 subheadings.
• 3916.90.10.00: Of acrylic polymers. This sub-heading specifically targets plastic rods made from acrylic polymers (e.g., PMMA - Polymethyl methacrylate, commonly known as acrylic).

Duty Information:

• Basic Duty: 6.5%
• Additional Duty: 25.0%
• Total Duty (Current): 61.5%
• Additional Duty (Post April 2, 2025): 30.0% (Total duty will increase to 66.5% after this date)

Example Products: PMMA rods used for lighting, acrylic rods for displays, acrylic plastic rods.

Important Considerations & Recommendations:

• Material Verification: Crucially, confirm the exact polymer composition of the plastic rods. The difference between ethylene polymers and other plastics (like acrylic) significantly impacts the applicable duty rate. Provide a material safety data sheet (MSDS) or a detailed product specification if possible.
• Cross-Sectional Dimension: Ensure the cross-sectional dimension of the rods exceeds 1mm, as this is a defining characteristic of these HS codes.
• Surface Treatment: Note whether the rods have undergone any surface treatment (e.g., coating, printing). This may affect classification.
• Single Invoice Value: Be aware of the single invoice value, as this can trigger different customs procedures.
• Certification: Depending on the end-use application of the plastic rods, you may need to provide specific certifications (e.g., RoHS, REACH). Please check the import regulations for your destination country.
• Post April 2, 2025 Duty Changes: Factor in the increased additional duty rate of 30% for shipments arriving after April 2, 2025.

Disclaimer: This information is for general guidance only and does not constitute professional customs advice. It is recommended to consult with a licensed customs broker or relevant authorities for accurate classification and duty assessment based on your specific product and import requirements.