Found 7 matching results
(CN → US)
| HS Code | Official Doc | Tariff Rate | Origin | Destination | Effective Date |
|---|---|---|---|---|---|
| 7218100000 | Doc | 30.0% | CN | US | 2025-05-12 |
| 7218990090 | Doc | 30.0% | CN | US | 2025-05-12 |
| 7222300001 | Doc | 30.0% | CN | US | 2025-05-12 |
| 7222300022 | Doc | 30.0% | CN | US | 2025-05-12 |
| 8311900000 | Doc | 55.0% | CN | US | 2025-05-12 |
| 8307903000 | Doc | 58.8% | CN | US | 2025-05-12 |
| 8307906000 | Doc | 58.8% | CN | US | 2025-05-12 |
Here's a breakdown of potential HS codes for "STAINLESS IRON BOARD STRIPS", based on the provided reference data. Given the description, multiple codes could apply, and the correct one depends on the precise characteristics of the strips.
- 7218.10.00.00 – Stainless steel in ingots or other primary forms; semi-finished products of stainless steel: Ingots and other primary forms. (First two digits '72' indicate iron and steel products. '.10' specifies stainless steel in its basic forms.) This code applies if the strips are supplied as raw material, not yet formed into a specific shape for the ironing board application.
- 7218.99.00.90 – Stainless steel in ingots or other primary forms; semi-finished products of stainless steel: Other: Other Other. ('.99' covers other stainless steel products not specifically classified elsewhere.) This is a broader category and would apply if the strips are semi-finished but don't fall into the more specific '.10' category.
- 7222.30.00.01 – Other bars and rods of stainless steel; angles, shapes and sections of stainless steel: Other bars and rods Electroslag or vacuum arc remelted. ('.30' indicates bars, rods, angles, shapes, and sections.) If the strips are formed into a defined shape (like a flat bar) and manufactured using electroslag or vacuum arc remelting, this code could be applicable.
- 7222.30.00.22 – Other bars and rods of stainless steel; angles, shapes and sections of stainless steel: Other bars and rods Other: With a maximum cross-sectional dimension of less than 152.4 mm: Containing less than 8 percent by weight of nickel. ('.30' indicates bars, rods, angles, shapes, and sections.) This is a more specific sub-category within '.30', applying to smaller strips with a nickel content below 8%.
Important Considerations & Recommendations:
- Material Composition: Confirm the exact stainless steel alloy used. Different alloys may have different classifications.
- Manufacturing Process: Determine if the strips were produced using electroslag or vacuum arc remelting.
- Dimensions: Measure the cross-sectional dimensions of the strips.
- Nickel Content: Verify the percentage of nickel in the strips.
- Form: Is it a raw strip, or has it been formed into a specific shape for the ironing board application?
Tax Implications (as of reference data):
- Codes 7218.10.00.00 and 7218.99.00.90 currently have a total tax rate of 30.0% (0.0% base tariff + 30.0% additional tariff after April 2, 2025).
- Codes 7222.30.00.01 and 7222.30.00.22 also have a total tax rate of 30.0% (0.0% base tariff + 30.0% additional tariff after April 2, 2025).
Disclaimer: HS code classification is complex and depends on the precise characteristics of the goods. This information is for guidance only and should not be considered definitive. It is recommended to consult with a qualified customs broker or relevant authority for accurate classification.