分装管

📦 Filling Tubes (for Packaging & Dispensing) – HS Code & Tariff Guide 2026 | Full Compliance & Clearance Strategy

🌐 HS Code Reference & Customs Clearance Handbook | 2026 Updated Tariff Rules | Expert-Level Trade Intelligence

🧩 One. Product Definition & Classification: What Exactly Is a "Filling Tube"?

A filling tube is a plastic or metal cylindrical container designed for packaging, dispensing, or storing liquids, gels, pastes, or aerosols—commonly used in cosmetics, pharmaceuticals, industrial chemicals, and food packaging.

In international trade, these are not just "tubes" — they are precision-engineered packaging solutions with specific material, shape, and function that determine their HS Code classification.

⚠️ Critical Distinction: - If it’s plastic, used for dispensing, and resembles a bottle or tube → Likely 3923.30.00.90 - If it’s metal (steel/iron), cylindrical, and used for pressurized gas or aerosol filling → Likely 7310.21.00.25 or 7310.21.00.70

🔍 Key Clues for Classification: - Material: Plastic vs. Metal (iron/steel) - Shape: Round cross-section, sealed ends, nozzle tip - Function: Filling, dispensing, pressurized storage (aerosol) - Form: Single-use, reusable, or part of a larger system

📦 Two. HS Code Breakdown (2026 Official Tariff Matrix)

✅ Why These Codes? - 3923.30.00.90: "Other plastic containers" under 3923.30 — for dispensing and packaging. - 7310.21.00.70 & 25: Covered under "cylinders, welded or rolled, of iron or steel" — used for aerosol or gas storage.

💰 Three. 2026 Tariff & Duty Breakdown (US Market – China Origin)

✅ Applicable Country: United States (US)
✅ Origin: China (CN)
✅ Effective Date: November 10, 2025 (inclusive)
✅ Legal Basis: IEEPA, USITC Section 301, Section 122

🎯 1. 3923.30.00.90 — Plastic Filling Tubes (Packaging & Dispensing)

📌 Explanation: - Base 3%: Standard tariff for plastic packaging. - +25%: From Section 301 (USITC) — targeting Chinese goods deemed unfair trade practices. - +10%: IEEPA (International Emergency Economic Powers Act) — imposed on Chinese-origin goods since 2025. - Total: 38% — high but lower than metal aerosol cans.

🎯 2. 7310.21.00.70 — Metal (Iron/Steel) Cylinders for Aerosol Filling

📌 Explanation: - 0% base duty: No standard tariff on steel cylinders. - +25%: Section 301 tariff (China origin). - +10%: IEEPA emergency tariff. - +50%: Special tariff on steel, aluminum, and copper products — applies to all metal containers made from these materials. - Total: 85% — extremely high — one of the highest tariffs in the entire tariff schedule.

⚠️ Critical Note:
Even if the cylinder is not pressurized, if it’s made of steel/iron, and used for aerosol or gas, it still triggers the 50% metal product surcharge.

🎯 3. 7310.21.00.25 — Metal Cylinders (Round Cross-Section), for Aerosol/Chemical Use

📌 Why Same as 7310.21.00.70? - Both codes fall under "cylinders of iron or steel". - Both are round cross-section, welded or rolled, used for pressurized storage. - No functional difference in tariff treatment — same 85% rate applies.

🛠️ Four. Customs Clearance Best Practices (Pro Tips to Avoid Penalties)

✅ 1. Required Documentation (MUST-HAVE)

✅ 2.申报技巧（Key Rules）

🔥 "Material First, Shape Second, Use Last — 38% vs 85% Depends on This!"

📌 Pro Tip:
Do NOT split a metal cylinder into “body” + “cap” + “nozzle” — even if they’re different materials.
The whole unit is taxed as the highest-duty component → 85%.

✅ 3. Special Cases & Solutions

🌍 Five. Global Customs Comparison (2026)

📌 Insight:
- USA is the only market with 85% tariff on metal aerosol tubes. - Switching to plastic can cut duty by nearly half. - Vietnam/Mexico origin can avoid IEEPA/301 tariffs.

📌 Six. Common Mistakes & How to Avoid Them

❌ Mistake 1: Misclassifying a metal aerosol cylinder as plastic
👉 Result: 38% vs 85% → $100k+ extra cost on 10,000 units

❌ Mistake 2: Splitting a metal tube into parts for申报
👉 Result: Each part taxed at 89.5% → Total 268%!

❌ Mistake 3: Using generic name like “tube” or “container”
👉 Result: Customs can reclassify → higher duty + penalties

✅ Correct申报 Name Example:

“Plastic Filling Tube, 30ml, for Skincare Cream, Round Cross-Section, with Plastic Nozzle, 1000 Units”

✅ Or: “Steel Aerosol Cylinder, 120ml, Welded, for Pressurized Gas, Round Cross-Section, 500 Units”

🎯 Seven. Final Verdict: Smart Strategy = Lower Cost, Faster Clearance

🔹 Plastic = 38%
🔹 Metal = 85%
🔹 Splitting = 268%
🔹 Origin matters: China = high duty, Vietnam = low duty

📣 Your Action Plan: 1. Verify material — plastic or metal? 2. Confirm shape — round cross-section? 3. Check use — aerosol? dispensing? 4. Choose origin wisely — consider Vietnam/Mexico for duty savings 5. Apply for Advance Ruling — get pre-approval on HS Code

🎉 Pro Tip: Use This Formula for Duty Savings

💡 If you switch from metal to plastic → Save 47% duty
💡 If you shift production to Vietnam → Save 85% duty
💡 If you avoid splitting → Save 183% tax risk

📣 🚀 Immediate Action:

📞 Contact a US Customs Broker + provide product photos + specs
📄 Request HS Code Pre-Ruling (Advance Ruling)
💼 Let your supply chain be tariff-smart, not tariff-stuck!

✨ Your product’s success starts with the right HS Code.
💼 One wrong classification = thousands in lost profit.
✅ Get it right — from the first shipment.

📌 Expert Insight:

“In 2026, material is destiny. Plastic = 38%. Metal = 85%.
Don’t let a tube cost you a fortune.”