large eye rivet

👁️ Large Eye Rivet (大号鸡眼铆钉)

🌐 HS Code Reference & Clearance Guide | 2026 Latest Tariff Analysis | Professional Customs Strategy
📌 I. Product Definition & Classification: What Exactly Is a "Large Eye Rivet"?

A Large Eye Rivet (commonly known as "鸡眼铆钉" in Chinese trade contexts) is a type of metal fastener characterized by a large, flat, circular head with a hole (eye) in the center. They are primarily used in the leather goods, footwear, apparel, and luggage industries for decorative purposes or to reinforce stress points (e.g., on belt loops, pockets, or bag handles).

Crucial Classification Logic:
The HS Code classification depends entirely on the Material and the Structural Form (Threaded vs. Non-threaded):

1. Base Metal (Iron/Steel/Aluminum/Copper/Zinc, etc.):
   • If the rivet is non-threaded (solid pin, pressed or hammered in), it falls under Chapter 73 (Articles of Iron or Steel) or Chapter 74 (Articles of Copper).
   • If the rivet is threaded (has screw-like threads to be screwed into place), it falls under Chapter 83 (Miscellaneous articles of base metal).
2. Material Specifics:
   • Iron/Steel: Most common. Classified under 7318.
   • Copper/Copper Alloy: Classified under 7415.
   • Other Base Metals (Zinc, Brass, etc.): Classified under 8308 (if non-threaded or specific classification rules apply) or 73/74 depending on specific alloy rules. Note: In the provided data, "Large Eye Rivets" made of non-iron/steel non-copper base metals are often grouped under 8308.20 for "eyelets, grommets..." or similar general fasteners if they don't fit strict 73/74 definitions, but usually, 8308 covers "Fasteners... of base metal, other than iron or steel".

⚠️ Key Distinction Point:
- Threaded Rivets: If it has visible threads and is tightened by rotation → HS 8308.
- Non-Threaded Rivets: If it is a solid piece installed by crimping/pressing:
- Iron/Steel → HS 7318
- Copper → HS 7415
- Other Base Metals → HS 8308

📦 II. HS Code Classification Details (2026 Latest Tariff Data from <DATA>)

Based on the provided <DATA>, here are the specific HS Codes, summaries, and tax structures for Large Eye Rivets:

🔍 Key Takeaway:
- Iron/Steel Rivets incur the highest taxes (85.0% - 87.8%) due to significant additional tariffs.
- Copper Rivets also face very high taxes (86.4%).
- Other Base Metal Rivets (likely Zinc, Brass, etc.) face a lower total tax of 35.0%.

💰 III. 2026 Latest Tariff Rate Breakdown (Detailed)

✅ Applicable Country: United States (US)
✅ Origin: China (CN)
✅ Effective Time: Current rates (Including Section 301 & IEEPA tariffs)

🎯 1. 8308.20.30.00 & 8308.20.60.00 —— Rivets of Base Metal (Other Than Iron/Steel/Copper)

📌 Explanation:
- These codes typically cover rivets made of Zinc, Brass, or Aluminum (if Aluminum is not classified under 76).
- The 0% base rate is offset by 25% from Section 301 and 10% from the 122 Clause (IEEPA).
- Total 35% is significantly lower than Iron/Steel or Copper counterparts.

🎯 2. 7415.33.10.00 —— Articles of Copper or Copper Alloy

📌 Explanation:
- Copper products face a 50% additional tariff on top of other surcharges.
- The combination of 1.4% + 25% + 10% + 50% = 86.4%.
- This is a punitive rate. Importers must consider cost implications heavily.

🎯 3. 7318.23.00.00 —— Screws, Bolts, Nuts, and Similar Articles, of Iron or Steel

📌 Explanation:
- Typically for threaded iron/steel fasteners.
- The 50% surcharge applies to all steel products.
- Total 85.0%.

🎯 4. 7318.29.00.00 – Other Screws, Bolts, Nuts, and Similar Articles, of Iron or Steel

📌 Explanation:
- Often for non-threaded or other specific steel fasteners not covered in 7318.23.
- Base rate is higher (2.8%), leading to the highest total tax of 87.8%.
- This is the most expensive category.

🛠️ IV. Customs Clearance Practical Advice (Real-World Pitfall Guide)

✅ 1. Preparation Checklist (Mandatory Documents)

✅ 2. Classification Strategy (Key Tips)

🔥 "Material Determines Tax, Form Determines Code!"

📌 Critical Warning:
- Do NOT assume all rivets are the same.
- Zinc/Brass/Aluminum rivets are much cheaper to import (35% tax) compared to Steel/Copper (85%+ tax).
- If your product is Zinc Alloy, ensure your supplier provides a material test report confirming it is not classified as Iron or Copper.

✅ 3. Special Circumstances

🌍 V. Global Market Comparison (2026 Latest)

📌 Conclusion:
- USA is the most expensive market for importing Large Eye Rivets from China.
- Zinc/Brass Rivets are significantly more cost-effective than Steel/Copper in the US market.
- Consider supply chain diversification (e.g., sourcing from Vietnam or Mexico) if shipping to the US to avoid high tariffs.

📌 VI. Common Errors & Pitfalls (Lessons Learned)

❌ Error 1: Declaring Zinc Rivets as "Iron/Steel"
👉 Consequence: Tax increases from 35% to 85% → Massive overpayment.
👉 Solution: Always provide material certificates for Zinc/Brass items.

❌ Error 2: Declaring Copper Rivets as "Other Base Metal"
👉 Consequence: Tax drops from 86.4% to 35% → High audit risk, penalties, and possible seizure.
👉 Solution: Be honest about material. Consider switching to Zinc if cost is a concern.

❌ Error 3: Ignoring the 122 Clause (IEEPA) 10%
👉 Consequence: Underestimating total landed cost.
👉 Solution: Factor in 10% additional IEEPA tariff for all China-origin goods.

❌ Error 4: Using generic terms like "Metal Accessories"
👉 Consequence: Customs may classify as duty-free or low-rate, then audit and reassess.
👉 Solution: Use precise terms: "Large Eye Rivet, Zinc Alloy, Non-Threaded".

✅ Correct Approach:

"Large Eye Rivet, Zinc Alloy, 6mm, Non-Threaded, Decorative Use for Leather Goods, HS 8308.20.30.00"

🎯 VII. Conclusion: Professional Classification Saves Money!

🎯 Remember the Rule:

🔹 "Zinc is King (35%), Steel is Pain (85%+), Copper is Expensive (86.4%)."
🔹 "Material is Key! Verify before you declare!"
🔹 "HS Code determines your profit margin!"

📌 Pro Tip:
If you are importing Large Eye Rivets from China to the US:
1. Check Material: If possible, use Zinc Alloy (8308) instead of Steel (7318) or Copper (7415) to save 50%+ in tariffs.
2. Pre-Ruling: Apply for a Customs Ruling if unsure about material classification.
3. Documentation: Keep Material Test Reports ready for customs audits.

📣 Immediate Action:

📞 Contact your freight forwarder with material specs.
🚀 Calculate Landed Cost: Include 35% (Zinc) or 85% (Steel) tariffs.
💼 Don't let customs taxes eat your profits!

✨ Professional Customs Clearance Starts with Accurate Classification!
💼 Every Percentage Point of Tax Matters!